The ideal oil for a Super 2 chain is Homelite Bar and Chain Oil. Clean SAE 30 oil can also be used to lubricate the chain, according to Homelite. If the temperature is below 40 degrees Fahrenheit, you can dilute the SAE 30 oil with kerosene..
Keeping this in consideration, can you use regular oil for bar and chain oil?
Motor Oil. Chain saw bar and chain oil isn't rated by SAE like traditional automobile motor oil. If your manufacturer's bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Subsequently, question is, can I use used motor oil in my chainsaw? No one recommends using old recycled motor oil. Some note that used motor oil could burn up your bar and chain sooner, which will make up for any cost savings. Used motor oil will sling off your chainsaw faster because it is already broken down.
Also, how do I lubricate my chainsaw?
How to Add Bar and Chain Oil to Your Gas Chainsaw
- Check and replace bar and chain oil regularly to reduce friction, keep the saw from wearing out faster, and to make cutting easier.
- Set on a level surface.
- Unscrew the cap and pour oil into reservoir – do not overfill.
- Screw cap back on and wipe down any excess oil.
What can I substitute for bar and chain oil?
Bar And Chain Oil Alternatives
- Motor oil. Motor oil is the most readily available alternative lube available.
- Vegetable oil. Vegetable oil is also a quite affordable bar and chain oil alternative.
- Canola oil. Canola oil shouldn't be confused with vegetable oil.
- Drained hydraulic fluids.
Related Question Answers
Can I use hydraulic oil for my chainsaw bar?
Hydraulic oil should not be used as bar oil. For one, it does not work as well for eliminating pitch on the bar. A quality bar oil will help reduce buildup of pitch on the bar and chain, which helps to reduce wear and increases cutting efficiency.Can I use vegetable oil instead of bar oil?
Tips for replacing chain oil with vegetable oil: Use canola oil – Canola oil is currently the most common environmentally compatible chain-and-bar lubricant. Vegetable oil is thinner – Vegetable oils have lower viscosities than the bar/chain lubricants and therefore flow more readily.What is the difference between chainsaw bar oil and motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry's tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.What can you use for bar chain oil?
Chainsaw Bar And Chain Oil Alternatives - Motor oil. If you find yourself in a situation where you need to use your chainsaw but you don't have any of the correct oil, one of the obvious options is motor oil.
- Vegetable oil.
- Canola oil.
- Drained hydraulic fluid.
Is there a difference in chainsaw bar oil?
All oils are not the same they are similar but by all means not the same. Autozone bar/chain oil runs like water. Stihl is tacky while others have more or less I've never had any problems with any major brand bar/chain oil from Stihl or the other companies.Can you run a chainsaw without bar oil?
Yes. You'll overheat and burn the bar and the chains without it. I tried used motor oil once - what a freeking mess~!!Can I use 10w30 for chainsaw bar oil?
Always use proper protective gear! The oil can be messy and oil on the lawn will kill the grass. Whenever I've used stray old bottles of automotive 10w30 as bar-chain oil, it just gave the impression that it wasn't as good. Not ideal, but works in a pinch.Can I use 2 stroke oil as bar oil?
Always use 2 stroke oil only for the mix. Oil is "relatively" cheap, compared to small engines. It is not worth the loss of lubrication and deposit control risk. Bar oil needs to be sticky in the summer for lubrication and to flow with "stickyness" for bar and chain lube in the cold.Should I run my chainsaw dry?
Re: To Run Dry Or Not? As long as you idle the saw while running out the last of the fuel, it should be fine. Just resist the urge to pull the throttle open to speed up the process as it will be running very lean for the last few seconds.What happens if you run a chainsaw without oil?
Chainsaw engines require a premixed fuel to keep them running at the proper temperatures. Without this oil in the gasoline, the piston will seize and the engine will be ruined. Nearly all gas chainsaws require a gasoline and oil mixture for their fuel.How much chainsaw oil do I need?
HOW MUCH 2-STROKE OIL DO I ADD TO MY FUEL? Most modern day chainsaws get best performance from a 50:1 fuel mix ratio - that is 2% oil or 20ml of quality two stroke oil per 1 litre of fuel. Some larger capacity saws over 65cc may require a 33:1 (30ml of oil per 1 ltr of fuel) or even 25:1 (40ml per 1 ltr).What weight is chainsaw bar oil?
For this reason, bar and chain oil should suit most loggers. They usually have a 10W relative weight during winter and 30W during warm weather conditions. You can check most oils authenticity by putting on the chainsaw and looking for any oil spills at about 8 inches on the other side.Can I use regular engine oil in a 2 cycle engine?
In short, any 2-stroke motor is a suitable place to use synthetic oil specially formulated for 2-stroke engines. Particularly where motors that have seasonal use are concerned, high-quality synthetic 2-stroke oil can be useful as among the additives you'll often find fuel stabilizer.Can I use engine oil as chain lube?
Using engine oil as a chain lubricant might serve you the purpose. Engine oil could get greasy at lower temperature or might even solidify. Improper lubrication would lead to chain wear, jerky transmission and added friction. Engine oil costs more than the chain lube.Can you use motor oil instead of bar and chain oil?
Motor Oil. Chain saw bar and chain oil isn't rated by SAE like traditional automobile motor oil. If your manufacturer's bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.Can I use olive oil in my chainsaw?
Use chain saws weekly at the farm and we use motor oil as chain lube often, no problems. Olive oil would just be more expensive. Olive oil tends to get a bit gummy when used as a lubricant, but if you clean it once in a while with a decent solvent it should be fine.Is vegetable oil a good lube?
Vegetable, canola, and other refined oils You can't just grab any oil from your kitchen to use as lube. Refined and hydrogenated cooking oils, such as vegetable oil and canola oil, go through heavy processing. This usually includes heating, bleaching, and chemical treatments.What kind of oil can I use for a chainsaw chain?
Petroleum-based bar oil has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer. Manufacturers of chainsaws make bar and chain oils specially blended for their machines to extend their lifespan, but if they are not available, the owner's manual suggests alternatives. 
