Apply Mapelastic AquaDefense liquid 6" (15 cm) on both sides of the cracks, control joints, corners and coves, using a paintbrush. Let dry to a dark green color. 2. Apply 2nd coat and let dry..
Just so, what is mapelastic AquaDefense?
Mapelastic AquaDefense is a premixed, advanced liquid-rubber, extremely quick-drying waterproofing and crack-isolation membrane for installation under ceramic tile or stone in residential, commercial and industrial environments.
Secondly, can you use AquaDefense on drywall? No. AquaDefense is not approved for showers constructed with drywall.
In this manner, how long does AquaDefense take to dry?
12 hours
Will Thinset stick to AquaDefense?
Aquadefense is a great waterproofing product. Thinset mortar will adhere to it that's what it's specifically manufactured for. It requires the use of a polymer modified / latex modified thinset mortar. Check out the library shower construction thread to make sure that you built your shower correctly so far.
Related Question Answers
What is AquaDefense?
Mapelastic AquaDefense is a premixed, advanced liquid-rubber, extremely quick-drying waterproofing and crack-isolation membrane for installation under ceramic tile or stone in residential, commercial and industrial environments.How do I get rid of AquaDefense?
Remove excess Mapelastic AquaDefense (while fresh) with damp sponge, soap and warm water. Any completely dried material may be mechanically removed.What color is aqua defense?
Cement-based thin-sets – such as MAPEI's Ceramic Tile Mortar, Ultraflex 1, Porcelain Tile Mortar and Ultraflex 2 – can be installed when Mapelastic AquaDefense turns to a dark green color (typically after 30 to 50 minutes).Can AquaDefense be painted over?
Yes the membrane gets hard after the waterproof is added and dried. You can put the mortar over and the tile adheres just fine. If you're using a waterproof board, you will use the AquaDefense and fabric on the seams but don't necessarily need to use over the whole wall.What is Red Guard waterproofing?
RedGard® is a liquid-applied elastomeric waterproofing material that cures to form a monolithic membrane. Benefits of Product in the Installation. Easy to use and can be applied by roller, trowel or airless sprayer. Rated for extra heavy duty service. Reduces curing time with quick-dry formula.What is waterproofing membrane?
A waterproofing membrane is a thin layer of water-tight material that is laid over a surface. This layer is continuous and does not allow water to pass through it. For example, on a flat terrace, a waterproofing membrane could be laid above the structural slab and below the finish tiles.How do you use mapelastic HPG?
Use 1/8" (3 mm) V-notched trowel, short-nap (3/8" [10 mm]) roller or paintbrush to apply Mapelastic HPG over area to be waterproofed at 40 mils (1 mm) thick. 3. Let Mapelastic HPG dry for 4 to 6 hours.Can you use Mapei AquaDefense on plasterboard?
plasterboard (for internal applications only); existing coatings in ceramic, terrazzo and stone; cementitious render. Mapei Mapelastic AquaDefense is a totally solvent-free, ready-to-use,ultra-quick drying, one-component light blue synthetic resin based paste in water dispersion.How soon can you tile after waterproofing?
24 hours
How long should Thinset dry before waterproofing?
Allow the RedGard membrane to cure for 1 to 1 1/2 hours. The color will turn from pink to a solid red sheet with no pink spots when it is fully dry. It is most important that you wait for the color of the product to turn completely red as ambient conditions will make the dry time vary.Can you tile over drywall in a shower?
The bottom line is that drywall (and this includes moisture resistant drywall) should never be used behind tile in wet areas (showers and tub-shower combinations). This is especially important in a shower located on an outside wall, but also helps even if the shower is on an inside wall.How long does it take for bathroom waterproofing to dry?
Once the sheets are installed, the waterproofer comes in and waterproofs the room as required. This ensures a tight water seal for years to come and no leaking showers! Waterproofing takes at least 24 hours to completely dry, this can be at least a 2-day process for 2-3 coats.Can I paint over RedGuard?
As long as you use a good primer, you should be OK, though. You can apply thinset over the RedGard and prime and paint over that. Joint compound is reactivated when it absorbs water and can cause problems like mold and blistering or delamination of paint film.Do you need to use RedGard over cement board?
As long as it's Cement Board & not some crappy "almost" cement board stuff. You really don't need the RedGard, but the more protection the betterso go for it. And yes, you can do the boards beforehand. But, hit the filled seams & screws (your weak points) as soon as a panel is ready to give it some time to setup.Is unmodified thinset waterproof?
All portland based cementious products will allow water to pass through. The latex modified is more resistant due to the latex that is mixed in with the adhesive but that doesn;t make it "waterproof". The latex also allows a bit more flex in the tile and substrate. As Jason described, thinset itself isn't waterproof.Does Thinset absorb water?
Cement board, backer board, thinset mortar, tile, grout and sealers aren't waterproof. Some tile absorbs very little, while grout and natural stone are porous as a sponge.Does 100% silicone stick to RedGard?
Caulk that gap with siliconized or latex caulk and then use Redgard over the caulk. Regard will not stick to 100% silicone caulk. You DO NOT want moisture collecting in that crevice and it can if you stuff it with thinset. Then after the tile is installed caulk that gap also.Can I use modified thinset with Kerdi?
Modified thinset mortars aren't recommended for use with Kerdi because they must dry out to gain strength, whereas the membrane inhibits drying, which can lead to unpredictable results. For example, if a shower is used before the mortar has cured properly, leaks and polymer leaching can occur. 
